Most problems people blame on composite decking, like bouncy boards, uneven gaps or wavy edges, actually start in the frame. Composite boards are made to precise dimensions, so they show every high joist, every twist and every gap that’s too wide. Build the subframe right and the boards go down quickly and stay put for decades.
This guide covers what a composite decking subframe needs. It isn’t a replacement for engineering advice: footings, bearer sizes and spans for your deck must follow AS 1684 (residential timber-framed construction), your local council’s requirements or an engineer’s design.
Timber or steel?
Composite decking can go on either kind of frame.
- Treated pine or hardwood is the most common choice. It’s easy to work with and familiar to most builders.
- Steel or aluminium subframes stay straight, won’t rot, and are often chosen for higher decks, rooftops and bushfire-prone sites.
Our fixing kits include colour-matched screws for both timber and metal subframes, so you can use either.
Get the joist spacing right
Joist spacing is the most important number in a composite deck. Space joists too far apart and the boards will flex between them.
HOME boards (138 × 23 mm), maximum joist centres:
| Use | Boards at 90° to joists | 60° | 45° |
|---|---|---|---|
| Residential | 450 mm | 400 mm | 350 mm |
| Commercial | 350 mm | 300 mm | 250 mm |
ADVANCED boards, recommended joist centres:
| Board and use | 90° | 60° | 45° |
|---|---|---|---|
| 140 mm, residential | 400 mm | 350 mm | 300 mm |
| 140 mm, commercial | 350 mm | 300 mm | 250 mm |
| 200 mm, residential and commercial | 450 mm | 400 mm | 350 mm |
Laying boards on an angle or in a herringbone pattern? Plan the closer spacing from the start. It’s very hard to add joists once the frame is built.
Leave enough ground clearance
Composite boards need air moving underneath them. Allow at least:
- 150 mm between the boards and soil
- 28 mm between the boards and concrete, for example when the deck sits on a slab using a low-profile frame
Good airflow keeps the frame dry and helps the boards handle temperature changes. Make sure water can drain away rather than pool under the deck.
Build it flat and true
- Level every joist. Check with a long straight edge or string line, and plane down or pack up any joist that’s out.
- Use joist hangers where joists meet bearers or walls, in line with the building code.
- Keep the tops of the joists in one plane. Clips need a flat surface to sit on, and any high spot will show through the boards.
Plan for the boards
A few details are easier to get right on paper than fix later:
- Every board must sit on at least three joists. Even a short 450 mm offcut needs a joist at each end and one in the middle.
- Overhang: boards shouldn’t extend more than 15 mm past the frame or fascia.
- Breaker boards: if your deck is longer than one board, plan a breaker board (a board laid across the run). It needs extra joists or noggings underneath to fix to.
- Picture framing: a border of boards around the edge needs blocking under the frame boards so every board has support.
- Fascia: fascia boards are fixed with at least 2 screws every 400 mm, so make sure there’s solid framing behind them.
Allow for expansion
Composite boards expand and contract with temperature, mostly along their length. The frame doesn’t move, so the gaps between board ends do the work. The gap depends on board length and the temperature when you install. A 5.4 m board needs 4 mm at 15 °C and 1 mm at 30 °C. Install below 30 °C, and fix each board in the middle (a TruLock clip or screws on the centre joist) so it expands evenly in both directions.
Before the boards go down
- Check that every joist is level and the spacing is correct.
- Confirm your clearance and drainage.
- Mark joist centres on the house wall and frame so the clips can be lined up.
- Get the full board quantity in one order, because colour can vary between batches.
Our DIY decking guide walks through laying the boards step by step. The full HOME and ADVANCED installation guides are on our Guides & Resources page. Use the decking calculator to estimate boards and clips, or find a Recommended Installer if you’d rather leave the frame to a pro.
Frequently asked questions
What joist spacing do I need for composite decking?
For HOME boards in a home, 450 mm centres with boards at 90° to the joists. ADVANCED 140 mm boards need 400 mm. Commercial decks and angled boards need closer spacing. Check the tables above.
Can I lay composite decking over an existing timber deck frame?
Often, yes, if the frame is sound, level and the joists are at the right spacing. Many older timber decks have joists too far apart for composite and need extra joists added.
Can composite decking go straight on concrete?
Not directly. It needs a frame (battens or a low-profile system) that gives at least 28 mm of clearance and lets water drain.
Do I need a building permit for my deck?
It depends on your state, the deck’s height and size, and whether it’s in a bushfire-prone area. Check with your local council or a building surveyor before you start.
See WoodEvo for yourself
Order free samples, or get matched with an accredited installer near you.